| Document Type
|
:
|
BL
|
| Record Number
|
:
|
743787
|
| Doc. No
|
:
|
b563735
|
| Main Entry
|
:
|
edited by Lucas F.M. da Silva ... [et al.].
|
| Title & Author
|
:
|
Testing adhesive joints : : best practices\ edited by Lucas F.M. da Silva ... [et al.].
|
| Publication Statement
|
:
|
Weinheim : Wiley-VCH, ©2012.
|
| Page. NO
|
:
|
xxviii, 440 p. : illustrations ; 25 cm
|
| ISBN
|
:
|
3527329048
|
|
|
:
|
: 9783527329045
|
| Contents
|
:
|
MANUFACTURE OF QUALITY SPECIMENS Preparing Bulk Specimens by Hydrostatic Pressure Preparing Bulk Specimens by Injection Preparing Bulk Specimens by Pouring Preparing Lap Joints with Flat Adherends SimpleMethods for the Preparation of Single Lap Joints Specimens Preparing Thick Adherend Shear Test Specimens Modified Thick Adherend Shear Test Preparing Butt Joints Preparing Napkin Ring Specimens Preparing T Joint Specimens Preparing Flexible-to-Rigid Peel Specimens Preparing Specimens for Fracture Properties: Double Cantilever Beam and Tapered Double Cantilever Beam Preparing Bonded Wood Double Cantilever Beam (DCB) Specimens Modified Arcan Test QUASI-STATIC CONSTITUTIVE AND STRENGTH TESTS Quasi-Static Testing of Bulk Tensile Specimens Uniaxial and Bulk Compression Quasi-Static Testing of Bulk Compression on Flat Specimens Iosipescu (V-Notched Beam) Test Arcan (V-Notched Plate) Test Quasi-Static Testing of Butt Joints in Tension Shear Properties of Adhesives Measured by Napkin Rings and Solid Butt Joints in Torsion Quasi-Static Testing of Thick Adherend Shear Test Specimens Modified Thick Adherend Shear Test Quasi-Static Testing of Lap Joints Modified Arcan Test Pin-and-Collar Test Method QUASI-STATIC FRACTURE TESTS Measuring Bulk Fracture Toughness Quasi-Static Fracture Tests: Double Cantilever Beam and Tapered Double Cantilever Beam Testing End-Notched Flexure Mode II Fracture Characterization of Bonded Joints Using the ELS Test The Notched Torsion Test to Determine the Mode III Fracture Properties of Adhesives Other Mixed Mode Adhesive Fracture Test Specimens Compact Mixed Mode (CMM) Fracture Test Method Mixed Mode Bending (MMB) with a Reeder and Crews Fixture Mixed Mode Fracture Testing Fracture of Wood Double Cantilever Beam (DCB) Specimens The T-Peel Test Peel Testing at 180? The Floating Roller Peel Test Climbing Drum Peel Test The Analysis of Peel Tests HIGHER RATE AND IMPACT TESTS Dynamic Elastic Modulus The Pendulum Impact Test for Adhesives and Adhesive Joints Higher Rate and Impact Tests: Fracture at High Rates High-Strain-Rate Testing of Adhesive Specimens and Joints by Hopkinson Bar Technique Clamped Hopkinson Bar Testing of Adhesive Bonds under Peel and Shear Loads at Increased Velocities DURABILITY Measurement of the Diffusion Coefficient Tests with Moisture Durability Testing Using Open-Faced Specimens Tests with Temperature The Wedge Test Fatigue Mixed-Mode Fatigue Testing of Adhesive Joints Measurement of Time-Dependent Crack Growth Curvature Mismatch Fracture Test for Subcritical Debonding OTHER TEST METHODS Thermal Characterization Dynamic Mechanical Analysis with a Vibrating Beam Method Bimaterial Curvature Method for Residual Stress and Thermal Expansion Coefficient Determination The Pull-Off Test Shaft-Loaded Blister Test Tests under Hydrostatic Pressure INDEX
|
| Subject
|
:
|
Adhesive joints -- Testing.
|
| Added Entry
|
:
|
et al
|
|
|
:
|
Lucas Filipe Martins da Silva
|